Atlas PV-10P lift Install - We Finish Installation - YouTube
In this video we are finishing up the installation. On this video, we position the posts, drill the anchor bolt holes, fill the holes half-full with special epoxy, pound in the anchor bolts, shim the posts until plumb, and torque the anchor nuts. Next video is the initial power-up ... View Video
Installation Instructions - Revolution Lift
LIFT HEIGHT W/ 3 1/2" ADAPTER 7 1/8" MIN. Tighten anchor bolts to an installation torque of 110 ft-lbs. Shim thickness MUST NOT exceed 1/2” when using the 5-1/2” long anchors of bolt. Drive anchor into hole until nut and washer ... Return Doc
Read This Entire Manual Before Operation Begins.
Read this entire manual before operation begins. This lift is an 9,000 lb. capacity, 2-Post Lifts. The locking latch system is very similar to an extension ladder. Check each anchor bolt with torque wrench set to 110 foot pounds. ... View Doc
INSTALLATION MANUAL & OPERATION INSTRUCTIONS
BOLT BOX CONTENTS 2 Post Lift: CJ 10,000 OHA INSTALLATION manual COMPLETE HYDRAULIC 10 Anchor Bolt 3/4 x 5 1/2" With Flat Washers & Nuts Tighten Anchor Bolts using a torque wrench to 125 ft. / lbs. ... Read Here
Model No. TP12KC-D 12,000 Lb Capacity Two Post Symmetric Lift
12,000 lb Capacity Two Post Symmetric Lift PLEASE READ ENTIRE MANUAL BEFORE or apply a small amount of torque to the bolt. If it is tight, 3’ from the nearest obstruction on the sides of the lift. 2. To install Anchor: ... Read Content
My New BendPak 2-Post Lift! - YouTube
In this episode we review, install and test our new BendPak XPR-10A 10,000 pound capacity 2-post asymmetrical lift! This heavy duty piece of equipment will a ... View Video
Rotary Lift
Rotary Lift Trouble Shooting Guide Page No. 1. Power Unit.. 2 2. Two Post Lifts Anchors not torqued correctly. 3. Torque bolts too correct spec. Locking latches do not 1. Latch pivot pins rusted. ... Retrieve Here
GL-9 MANUAL 9,000 POUND TWO POST GOLF LIFT
9,000 POUND TWO POST GOLF LIFT 2003C GOLF LIFT underneath the base plate and around the anchor bolt. Tighten 3/8 anchor bolts to 25 ft-lbs. of torque. STEP 16: Install the half moon gear locks on each swing arm (USA side up). ... Fetch Here
7000LBS 2-POST LIFT Model 94844
7000LBS 2-POST LIFT Model 94844 INSTALLATION, OPERATION & MAINTENANCE MANUAL Torque wrench: 150 foot pounds minimum k. 12 ft. Step ladder Assemble washer and nut to anchor with nut just below impact section of bolt. Drive anchor into hole until nut and washer contact base. ... Document Viewer
M1-4.5 & M1-6.5 SINGLE POST LIFT INSTALLATION & OWNER’S MANUAL
SINGLE POST LIFT . INSTALLATION & OWNER’S MANUAL. This lift is a 2-Post Lift. The locking latch system is very similar to an extension ladder. Check anchor bolt tightness. Torque anchor nuts to 150 foot-pounds. Do not use impact. If ... View This Document
Concrete Requirements - Rotary Lift
CONCRETE REQUIREMENTS Below you will find the concrete thickness, strength, anchor torque and specifications for concrete pads if the above is not attainable. Lift Model # Min Anchor Embedment Concrete *On all Two post models; If anchors do not tighten to specified torque, ... Fetch Doc
Screw - Wikipedia
American name British name Description; anchor bolt: A special type of bolt that is set in wet concrete, with the screw threads protruding above the concrete surface. ... Read Article
MODEL Q10000 TWO POST - Nytechsupply.com
MODEL Q10000 TWO POST 10,000 lbs Capacity 2,500 lbs per Arm INSTALLATION, OPERATION MANUAL 2. Lift Height: Tighten anchor bolts to an installation torque of 150 ft.-lbs. Shim thickness MUST NOT ... View Full Source
Two Post Clear Floor ‘Bi-Symmetric’ Automotive Lift 11,000 lb. Capacity Installation & Operation Manual The 2-post hydraulic lift should be installed on level ground. anchor bolt. Carefully tap anchor into hole. ... Doc Viewer
Model 165948 Two-Post Clear Floor Lift
165948 Two Post Lift Installation and Owners Manual 2 TABLE OF CONTENTS Important Information Check anchor bolt tightness. If the anchor bolts are loose, Torque wrench 15/16” deep socket ... Get Content Here
General Two-Post Car Lift Safety Warnings - BendPak
General Two-Post Car Lift Safety Warnings . If the anchor bolts were loosened to aid on the installation of the top trough, make sure to tighten the anchor bolts. Tighten carriage-stop bolt to 2 - 3 ft-lbs. of torque ... Doc Viewer
TWO COLUMN AUTOMOTIVE LIFT PRO V10 10,000 - Direct Lift
TWO COLUMN AUTOMOTIVE LIFT Two Post Lifts Check each anchor bolt with torque wrench set to 85 foot pounds. STEP 7: Using a level, check column for side-to-side plumb and front-to-back plumb. If needed, use horseshoe shims provided by ... Access Doc
2-Post Lift Concrete Requirements
2-Post Lift Concrete Requirements Toll Free: 800.648.5438 Challenger Lifts, Inc. reserves the right to make changes without notice and without making changes retroactive. 2-Post Concrete Requirements 6-05. Rev. 8/22/03 I diameter x 1 1/2” lg shoulder bolt and 1/2”-13 nylon lock ... Return Document
Anchor bolt - Wikipedia
An anchor bolt is a fastener used to attach objects or structures to concrete. There are many types of anchor bolts, consisting of designs that are mostly proprietary to the manufacturing companies. ... Read Article
12,OOO LB. 2-POST AUTOMOBILE LIFT
12,OOO LB. 2-POST AUTOMOBILE LIFT IMPORTANT Reference ANSI/ALI ALIS, expansion joint, or abandoned anchor hole is 2-3/4”. anchors do not tighten to 150 ft-lbs. Installation torque, ... Fetch Full Source
INSTALLATION / OWNERS MANUAL
INSTALLATION / OWNERS MANUAL. TWO COLUMN 10K LIFT (PV10) Two Post Lifts 1. Check each anchor bolt with torque wrench set to 85 foot pounds. STEP 7: Using a level, check column for side-to-side plumb and front-to-back plumb. If ... Get Content Here
Two Post Lift Manual - Forward Lift | Car lift, Auto lift ...
Two Post Lift Manual DP15, DP15-2 Capacity 15,000 lbs. 2. With lift lowered check the hydraulic fluid level. If necessary add oil as described in the Installation Instruction section of this manual 3. Check anchor bolt tightness. ... Retrieve Doc
INSTALLATION / OWNERS MANUALS - Revolution Lift
INSTALLATION / OWNERS MANUALS Read this manual thoroughly before installing, This lift is an 9,000 lb. capacity, 2-Post Lift. Check each anchor bolt with torque wrench set to 150 foot pounds. STEP 8: ... Content Retrieval
Hydraulic torque wrenches use hydraulics to tighten or loosen a nut or bolt. This type of wrench uses a predetermined amount of torque and can operate more quietly than similar pneumatic wrenches, OUR TORQUE WRENCH
ReplyDeleteThere are many variations of wrenches that are available in the market and one of the most popular ones is the torque wrench. click here
ReplyDeleteBefore even start to use torque wrench make sure All torque wrenches that are used on aircraft are regularly inspected, tested and calibrated by a facility equipped to do so.if the serviceable tag indicates as expired. DO NOT USE THE TOOL. visit website
ReplyDeleteOf the two types of torque wrenches, the micrometer wrench is definitely the more accurate. Typically, they are rated as being accurate to four percent of torque set. However, this accuracy can easily be lost if the wrench is not reset to zero before storage. Beam wrenches don't have this possibility of losing their accuracy, click to read
ReplyDelete